Neon Flex™ 50mm Aluminium Mounting Channel

Part Num: LN-FX-5

A 50mm aluminium channel clip with two mounting holes and comes supplied with 2 x cross head screws.
Neon Flex™ Connector Pins

Neon Flex Front connection pins. Male 2 pin smooth to Male 2 pin barbed, used at the beginning of an LED strip, when connecting between Power Supply and LED Neon. The barbed end is pushed into the Neon Flex, smooth pins connect to the power cable.

Neon Flex™ 1M Aluminium Mounting Channel

Part Num: LN-FX-CH

Neon Flex Aluminium mounting channel in 1M lengths, can be cut down to desired lengths.
 
Neon Flex™ End Caps

For sealing ends of the Neon Flex, securing and preventing water ingress.

Neon Flex™ Heatshrink Tubing

Heat Shrink to be used to seal the connectors and End Caps after these have been fitted to the Neon Flex using the Glue above.
Neon Flex™ Glue

The Glue is used inside the End Caps and Power Lead Cap to seal and bond them to the Neon Flex.

Neon Flex™ 600mm Middle Connector Cable

Part Num: MIDDLE_CONNECTOR_CABLE_1

LED Flex Neon Middle Connector Cable designed to be used to create a gap in a run of Neon Flex or to allow a run to go around the corner of a building for example. Comes in 600mm lengths.

Supplied with 2 Connection Pins and 2 Heat Shrinks.
Neon Flex™ Power Cable

Mains 230VAC power supply which is capable of powering up to 50 meters of LED Neon Flex. Comes supplied with output cable with a molded front end connector for Neon Flex Plus.
Neon Flex™ Plus - 240V Accessory Kits
Part Num: ACCSFOR240VNEONFLEX

These contain: 5 x Front connection pins, 5 x End caps, 5 x Power leads with AC-DC convertor moulded in line, 10 x pieces of Heatshrink and a bottle of Glue.

5 x End Caps
5 x End Caps
5 x Connector Pins
5 x Connector Pins
10 x Heatshrink Tubing
10 x Heatshrink Tubing
Glue
Glue
5 x Power Cable
5 x Power Cable
Neon Flex™ 24V Transformer

Part Num: POWER_CORD_LN_FX_24V_4A

A sealed 24V transformer  with an output cable complete with moulded end cap suitable for the Neon Flex. This will drive a maximum of 15M of 24V Neon Flex.
Glue
Glue
Neon Flex™ Glue

The Glue is used inside the End Caps and Power Lead Cap to seal and bond them to the Neon Flex.
10 x Heatshrink Tubing
10 x Heatshrink Tubing
Neon Flex™ Heatshrink Tubing

Heat Shrink to be used to seal the connectors and End Caps after these have been fitted to the Neon Flex using the Glue above.
5 x End Caps
5 x End Caps
Neon Flex™ End Caps

For sealing ends of the Neon Flex, securing and preventing water ingress.

5 x Connector Pins
5 x Connector Pins
Neon Flex™ Connector Pins

Neon Flex Front connection pins. Male 2 pin smooth to Male 2 pin barbed, used at the beginning of an LED strip, when connecting between Power Supply and LED Neon. The barbed end is pushed into the Neon Flex, smooth pins connect to the power cable.
Part Num: ACCS_KIT_24V_LN_FX(C)

These contain: 5 x Front connection pins, 5 x End caps, 5 x Power leads with AC-DC convertor moulded in line, 10 x pieces of Heatshrink and a bottle of Glue.

Neon Flex™ Plus - 24V Accessory Kits
Additional Neon Flex™ Plus Accessories
50mm Aluminium Channel
50mm Aluminium Channel
1m Aluminium Channel
1m Aluminium Channel
2m Aluminium Channel
2m Aluminium Channel
Neon Flex™ 2M Aluminium Mounting Channel

Part Num: LN-FX-CH-2M

Neon Flex Aluminium mounting channel in 2M lengths, can be cut down to desired lengths.
Middle Connector Cable
Middle Connector Cable
24V Transformer
24V Transformer
ACC 5M Power Cord
ACC 5M Power Cord
OR
Neon Flex™ ACC 5M Power Cord for LN-FX 24V Only

Part Num: POWER_CORD_24V_NEON_FLEX

This is a 5m 2 core cable with a moulded end cap to connect to the 24V Neon Flex. Customers will need to provide their own 24V DC regulated power supply.
© 2014 - 2017 Neon Flex     |     All rights reserved                                                                                                                        www.neonflex.co.uk